HART Transmitter Power Supply, Input Isolator LB3002A2

1-channel
Power supply for 2- or 3-wire transmitters with 4 mA ... 20 mA
Installation in Zone 2 or safe area
Supply circuit 15 V (20 mA)
Input from active signals of 4-wire transmitters
HART communication via field bus or service bus
HART communication also for separately powered devices
Simulation mode for service operations (forcing)
Line fault detection (LFD) and Live Zero monitoring
Permanently self-monitoring
Module can be exchanged under voltage

Technical Data
Product Documentation
Approvals
Vous sollicitez un expert

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Téléchargez ici la fiche technique complète en PDF ::

Caractéristiques techniques LB3002A2

Supply
Connection		backplane bus
Rated voltage		12 V DC , only in connection with the power supplies LB9***
Power dissipation		0.4 W
Power consumption		1 W
Internal bus
Connection		backplane bus
Interface		manufacturer-specific bus to standard com unit
Analog input
Number of channels		1
Suitable field devices
	Field device	pressure converter
	Field device [2]	flow converter
	Field device [3]	level converter
	Field device [4]	Temperature Converter
Field device interface
	Connection	2-wire transmitter
	Connection [2]	3-wire transmitter
	Connection [3]	4-wire transmitter
Connection		2-wire transmitter (HART): supply circuit: 2/3+, 4/5- 3-wire transmitter (HART): supply circuit: 2/3+, 6- measuring circuit: 4/5+, 6- 4-wire transmitter (separately powered): measuring circuit: 4/5+, 6- HART measuring circuit: 1+, 6-
Transmitter supply voltage		min. 15 V at 20 mA ; 21.5 V at 4 mA
Input resistance		15 Ω (terminals 5, 6) 236 Ω (terminals 1, 6) HART
Line fault detection		can be switched on/off for each channel via configuration tool , configurable via configuration tool
	Short-circuit	factory setting: > 22 mA configurable between 0 ... 26 mA
	Open-circuit	factory setting: < 1 mA configurable between 0 ... 26 mA
HART communication		yes
HART secondary variable		yes
Transfer characteristics
Deviation
	After calibration	0.1 % of the signal range at 20 °C (68 °F)
Resolution		12 Bit (0 ... 26 mA)
Refresh time		100 ms
Indicators/settings
LED indicator		Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) Status LED (2) yellow: Live Zero monitoring
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2006
Conformity
Electromagnetic compatibility		NE 21:2007
Degree of protection		IEC 60529:2000
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 when mounted on backplane
Connection		removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm²) or screw terminals (0.08 ... 1.5 mm²)
Mass		approx. 90 g
Dimensions		16 x 100 x 102 mm (0.63 x 3.9 x 4 inch)
Data for application in connection with hazardous areas
Output
	Voltage	27 V
	Current	87 mA
	Power	575 mW (linear characteristic)
Certificate		BVS 13 ATEX E 038 X
	Marking	II 3 G Ex nA [ic] IIC T4 Gc
Galvanic isolation
	Input/power supply, internal bus	safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012 EN 60079-11:2012 EN 60079-15:2010
International approvals
IECEx approval		BVS 13.0043X
	Approved for	Ex nA [ic] IIC T4 Gc
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	American Bureau of Shipping	T1450280/UN
	Bureau Veritas Marine	22449/B0 BV

Classifications

System	Classcode
ECLASS 13.0	27210120
ECLASS 12.0	27210101
ECLASS 11.0	27210120
ECLASS 10.0.1	27210120
ECLASS 9.0	27210120
ECLASS 8.0	27210120
ECLASS 5.1	27210120
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: LB3002A2

Product Documentation: LB3002A2

Safety and Security Documentation	Langue	Type de fichier	Taille
Manuel d'instructions	FRA	PDF	82 KB
Manuals
Manual	ENG	PDF	5367 KB

Approvals: LB3002A2

Declaration of Conformity	Identification	Langue	Type de fichier	Taille
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-1040C	ALL	PDF	1039 KB

Remarques générales sur les informations produit de Pepperl+Fuchs

Accès direct

Une passerelle vers l'Industrie 4.0

Certifiée Zone 2 et Classe I/Div. 2, la nouvelle passerelle PROFINET d'E/S déportées de Pepperl+Fuchs ouvre la voie à des applications de l'Industrie 4.0 dans les industries de transformation.

Pepperl+Fuchs AG
Längfeldweg 116
2504 Biel/Bienne
Suisse
info@ch.pepperl-fuchs.com
phone +41 32 374 76 76

Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.

Non disponible à la vente